Comdial FX Series Especificaciones Pagina 46
- Pagina / 172
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Dimensions (approximate):
Width (inches): 19 (including brackets)
Height (inches): 14
Depth (inches): 14.25
Weight (pounds): 36 (estimated with all cards)
72 (all components plus battery back-up assembly)
Memory Retention after Power Loss
65 hours typical—without battery back up
Music Interfaces (Two Inputs)
Input Level: 3 Volts peak-to-peak maximum
Input Impedance: Approximately 500 Ohms
Connector: Modular jack
Operating Environment
Temperature: 32–122 degrees F (0–50 degrees C)
Humidity: 90 percent relative, non-condensing
Heat Dissipation (Fully loaded cabinet): 1474 BTUs per hour
PA Port
Output Level: 400 Millivolts peak-to-peak (typical speech)
Output Impedance: Approximately 500 Ohms
Connector: Modular jack
42 – Knowing the Specifications
GCA40–242 General Description
- GCA40–242.04 4/02 1
- Contents 3
- Introducing the FX II 5
- Understanding the FX II 6
- Understanding the 7
- Telephone Features 7
- GCA40–242 General Description 10
- Using Impact Telephones 12
- Impact Telephones 14
- 8012S, 8112S 15
- 8024S, 8124S 15
- 2122S (22-Line Speakerphone) 16
- 9.08" 17
- 8.90" 17
- 1.13" 17
- 4.78" 17
- 3.94" 17
- Reviewing the Hardware 19
- 16 – Reviewing the Hardware 20
- Defining the Line Boards 21
- Defining the Station Boards 22
- Reviewing the Hardware – 19 23
- Locating the Boards 24
- Reviewing the Hardware – 21 25
- 22 – Reviewing the Hardware 26
- Mounting Considerations 27
- Using the Power Supply 28
- Using the Battery Backup 29
- 26 – Reviewing the Hardware 30
- Connecting the System 31
- Connecting the Stations 32
- Connecting the System – 29 33
- Connecting the IST Module 34
- MUSIC 1 = Pins 2 and 5 35
- MUSIC 2 = Pins 1 and 6 35
- Typical Industry Standard 36
- Non-electronic Telephone 36
- (Power Failure Interface) 36
- Connecting the System – 33 37
- (Front View of Jacks) 38
- Knowing the 39
- FX II Specifications 39
- Ringing Cadences 49
- FX II Features List 55
- Defining the Features 57
- Abandoned Hold Release 57
- Access Denied 57
- Account Code Button 57
- Alternate Attendant 59
- Answer Button 59
- Area Paging Interface 59
- New Features 59
- Feature Enhancements 61
- Automatic Hold—Line to Line 65
- Automatic Pause Insertion 66
- Automatic Privacy 66
- Automatic Redial 66
- Automatic Reports 67
- Automatic Route Selection 68
- Automatic Station Relocation 69
- Battery Backup Interface 71
- Block Programming 71
- Busy Button Inquiry 71
- Caller ID RNA—Ring–No–Answer 73
- Call Forward—All Or Personal 73
- Call Forward—Immediate 74
- Call Forward Outside System 74
- Call Forward, Recall 75
- Call Forward to Hunt Groups 75
- Call Park 76
- Call Park Recall 76
- Call Pick-Up Directed 76
- Call Pick-Up Group 76
- Call Pick-Up System 76
- Call Transfer—Screened 77
- Call Waiting Tone 77
- Camp-On—Call Waiting 78
- Camp-On—No Answer 78
- Central Message Desk 78
- Channel Negotiation 79
- Clear Major Alarm Ring 79
- Communications Card Support 80
- Conferencing—Multiline 80
- Conference Advisory Tone 80
- Console Support 80
- Consoleless Operation 81
- Consultation Hold 81
- Copy Model 81
- COS Time of Day Routing 81
- Database Program Storage 82
- Database Programming 82
- Data Interface Unit Support 82
- Day One and Day Two Ringing 83
- Day Restriction Level 83
- Daylight Saving Time 83
- Delayed Ringing 84
- Delayed Hot Line Operation 84
- Diagnostics (Limited) 84
- Dial 0 For System Attendant 84
- Dial By Name 85
- Dial Pulse Interdigit Time 86
- Digit Q and Z Position 86
- Direct-In Lines (DIL) 87
- Direct Inward Dialing (DID) 87
- How DISA Functions 89
- Direct Line Access by Station 90
- Direct Line Group Selection 90
- Disconnect Supervision 90
- Discriminating Ringing 90
- Do Not Disturb (DND) 90
- Do Not Disturb (DND) Inhibit 91
- Do Not Disturb (DND) Override 91
- DSS/BLF Console Support 91
- DSS Status Button 91
- Digital Voice Announce 91
- DVA/DISA 95
- DVA/Tracker 97
- Dynamic Save Button 98
- E1 Digital Carrier 98
- E911 Line Type 99
- End-to-End DTMF Signaling 100
- End-to-End Signaling on Lines 100
- Enhanced Night Mode 100
- Enhanced Ringing 101
- Executive Override Block 102
- Exclusive Hold 102
- ExecuMail Integration 102
- Executive Override 102
- Extended DTMF Tones 103
- Feature Inhibit 103
- Feature Renumbering 104
- Flexible Ringing Assignments 104
- Force Monitor Mode 105
- General Description GCA40–242 107
- Hookswitch Timer and 108
- Hot Transfer 108
- I Hold and I Use Indications 108
- Idle Line Preference 109
- Idle Line Priority 109
- Idle System Restore 109
- Interactive Button Support 112
- Intercom Number 113
- Intercom Hunt List 114
- Intercom Time-out 114
- Intercom Call Progress Tones 114
- Intercom Inter-Digit Dialing 114
- ISDN-PRI Interface 115
- Key/Hybrid Configuration 117
- Last Number Redial 117
- Line Access Restriction 117
- Location Code 119
- Lock Button 120
- Loop-Start Line Board with 120
- Manual Exclusion 121
- Manual Reset 121
- Mark Problem Line 121
- Master Clearing the System 122
- Maximum Call Duration 122
- Meet-Me Answer Page 122
- Message Deposit 122
- Message Waiting 123
- MF-DID/EM Line Board Support 123
- Mnemonic Programming 123
- Modem Support 123
- Names (Station and Lines) 125
- Networking Features 125
- Night Ringing 127
- Pause Time 129
- PC Attendant 129
- Periodic Line Tone 129
- Personal Intercom Number 129
- Privacy Release 131
- Private Lines 131
- Program Printout 131
- Programming Port 132
- Pulse/Tone Switchable 132
- Quick Transfer 133
- Recall/Flash (TAP) 133
- Station Headset Mode 137
- Ring on Busy 137
- Ringing Line Preference 137
- Save Button Dial Storage 138
- Saved Number Redial 138
- SCbus Interface Support 138
- Screened Call Transfer 139
- Secure Account Code Display 140
- Self Diagnostics 140
- Serial Data Port 140
- Service Observing 140
- Shift Button 140
- Silent Mode Button 141
- SMDA Reports 141
- SMDA Report Types 141
- Station Camp-On, Callback 143
- Station Class of Service 143
- Station Hunting 143
- Station Name 147
- Station Speed Dial 147
- Station Transfer Recall 148
- Subdued Ringing 149
- Synchronized Ringing 149
- System Clock 149
- System Speed Dial 149
- Interactive Button 150
- Toll Restriction 153
- Tone on Hold 154
- Tracker Paging System 154
- Transfer/Conference Button 156
- Transfer Recall 156
- Transfer Ring Cadence 156
- Unscreened Call Transfer 156
- Unsupervised Conference 156
- Voice Mail Integration Digits 157
- Voice Announce Blocking 158
- Voice Mail Ports 158
- VMMI Backwards Compatibility 159
- Zone Paging 161
Relacionado con productos y manuales para Contestadores automáticos Comdial FX Series
Contestadores automáticos Comdial 8024S Especificaciones
(438 paginas)
(438 paginas)
© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales